![]() My recomendation is to buy The Pocket Torch - Mini Butane Torch - PB207, that little torch works great, is easy to fill and lights every time perfectly, but no lanyard. One thing i like is its attached to a snap ring and i can attach it to the inside of my tractor cab so it stays warm and ready for use. This Flickery Flame Soldering kit includes the parts needed to create a compact, bright, portable simulated fire perfect for Jack-O-Lanterns, luminarias, holiday displays, scale models, and stage props. Now for the bad, you have to push 2 buttons to get this thing lit and you have to hold one in to keep the flame going and those buttons require lots of pressure, when lighting a fire in the cold it is a real pain. Make an awesome flickering flame for your decorations, models, luminarias, and props. it was hit and miss for several lighings, at last i got it to work regularly. Flickery Flame Soldering Kit LEDs color: White and Warm White Offers a compact, bright, portable simulated fire Perfect for holiday displays, decorations, luminarias, etc. ![]() i messed with it and tapped it and when at last i got it relit i held it on, i realized that it must be clogged, then the clog cleared after much tapping and banging and i got a nice butane flame. i got it loaded and finally got a flickery little flame. i could not get the lighter to light, i messed with it until my fingers were sore, so i added more butane, well i thought i did, the filler window is hard to see. So, three off-the-shelf white kits should work fine, but if you were using the red/yellow kits, you would want to substitute in a different resistor value, perhaps 150 ohms or so.Upon reciept of this item i dug it out of the plactic container, first thing the light didnt work, i opened up the battery compartment and the batteries were corroded, so i took a knife and scraped them and took an old tooth brush and cleaned the battery holder out, and i got the light to work. One note is that our white Flickery Flame kits are designed to run from 4.5 V DC, but the red/yellow Flickery Flame kits are designed to run from 3 V. If your machine’s output circuit was rated for 0.25 A, then you would have enough power to run three Flickery Flame kits off of that one output. You could also run flickery flame kits directly from that 4.5 V DC. 6.3 V AC will give you roughly 4.5 V DC with this circuit– enough voltage to power two LEDs in series, or one in series with a resistor. This circuit can be made as simply as four diodes plus a capacitor, or with an off-the-shelf bridge rectifier (e.g., Jameco Part number 178001, $0.29) and a capacitor (say Jameco part number 93761). You can read more about this see an example application, here: Īs far as the AC goes, I would recommend that you build a basic AC to DC converter, such as the “Full-wave Rectifier with Smoothing Capacitor” described here: ![]() With several flickering LEDs, each in series with several more LEDs, you can make a wide and striking effect. For example, one flickering can be used in series with one or more non-flickering LEDs, and will cause all of the LEDs in that series-driven set to flicker together. However, there are some good ways to get the basic result that you are after. Think of the processor in each LED as being a bit like a computer– when you remove power (whether that’s by switching it with AC or by putting it in series with an LED that blinks off its power), it reboots, and never gets to run its flickering program. The flickering LEDs cannot be used in series, nor directly driven by AC. This lighting effect uses a single 20 watt halogen lamp (the same as those used for domestic down lights) to mimic its. Bulb type: LED Light type: Warm yellow flickering flame Power: Solar Solar module: 0.88 W at 17 efficiency LED life span: 50,000 hours Brightness: 35 lm.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |